Produse pentru plasă de beton (24)

Optigrun Drainage Material Perl 2-10 LA is used as a drainage layer beneath intensive green roofs without water accumulation, for pressure resistant filling of Drainage Boards and as pressure resistant drainage and equalization layer beneath paving. Material:Lava Grading:2 - 10 mm Salt content:< 1.0 g/l Max. water capacity:14 - 18 Vol% Water permeability:180 - 450 mm/min Weight dry:min. 1,000 kg/m³ Weight when saturated:max. 1,300 kg/m³

Osmocem N gray Cement compound for the preparation, with the sole addition of water, of a waterproofing osmotic coating that can create horizontal and vertical barriers, also suitable in conditions of negative hydrostatic thrust vis-à-vis water permeation in the buildings. Typical uses include waterproofing underground rooms, elevator compartments, garages, basements, tanks, etc. The action of the active components and of the adhesion promoters of Osmocem N, saturated by the reaction the support capillaries, forming a complex system of gel and stable crystals, which results in the best sealing, effective even in conditions of negative hydrostatic thrust, without hindering the breathability of the walls. Osmocem N is compatible for food substances: is certified as suitable for the containment of foodstuffs and drinking water (Certificate no. 02/2010 Laboratorio Analysis Service di Settimo di Pescantina - VR). Osmocem N waterproof test: • Resistance to positive hydraulic thrust, UNI EN 12390/8: water penetration depth with 5 bar pressure = 1-2 mm (*) • Impermeability to negative hydraulic thrust, UNI EN 12390/8 modified (concrete support a / c ratio 0.7): no passage of water with a pressure of 1.5 bar (*) concrete with penetration depth <= 20 mm are considered waterproof. Waterproofing rigid structures and masonry walls underground, buried or in any case subject to water permeation: lift wells, basements, tanks, pipes, tunnels, garages, bridges, reservoirs, areas containing food, etc. in conditions of positive and negative hydrostatic thrust provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Osmocem N and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 19-20% (for interventions in the form of a spatula) or 21-22% (for interventions using a brush with long bristles). After mixing is completed wait a few minutes before applying. If applied by brush, roll out two or more crossed coats. Although it is not a specific product for finishing thick coats, it can still be used for these purposes. In these cases, it is appropriate to use a fibreglass mesh Armaglass 160. Approximately 1.7 kg/m² of Osmocem N for each millimetre of thickness to be made. Packaging: 25 kg bag UM: €/kg

Tungrit, ein Wolfram Granulat, ist im Plansee Online Shop verfügbar. Für chemische Analysen oder als Ausgleichmasse ist das Tungrit Granulat genau die richtige Wahl. Einfach und schnell im Onlineshop des Herstellers bestellen: www.plansee.com/shop

COMPOSITION ET ASPECT Ciment spécial, sable et divers adjuvants. La pâte est de couleur foncée. SUPPORTS ADMIS • Béton • Brique en terre cuit • Brique réfractaire DOCUMENTS À CONSULTER DTU 20.1 et DTU 24.1. CARACTÉRISTIQUES TECHNIQUES • Temps de prise : 30 mn • Température admise après séchage complet : 1000 °C CONDITIONNEMENTS Sacs de 5 et 25 kg sur palette houssée. STOCKAGE 6 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les supports doivent être propres, dépoussiérés, durs et exempts de toute trace d’agents séparateurs. Les supports très poreux ou par temps chaud devront être préalablement humidifiés. TAUX DE GÂCHAGE Environ 3 à 4 l. d’eau par sac de 25 kg. APPLICATION Appliquer à l’aide d’une truelle à maçonner puis d’un fer à joints. Entre deux briques, créer un joint d’environ 1 cm et en retrait de 5 à 7 mm par rapport aux bords.

Rapid Set CONCRETE MIX ist ein auf BCSA-Zementtechnologie basierender, mineralischer, multi-funktionaler Schnellreparaturmörtel für Schichtdicken von 50 - 600 mm. Geeignet für Betoninstandsetzung, Reparatur und Bau von Gehwegen, Fahrbahnen, Beton- und Maschinenfundamente, Schalungsarbeiten sowie Industrieböden, für innen und außen, auch in Nassbereichen. Erstarrungsbeginn nach ca. 15 Minuten, belastbar nach ca. 1 Stunde. Eigenschaften:für Reparatur und Neubau horizontal und vertikal spannungsarm Lieferform:25 kg Papierspezialverpackung

CBG-DP-90 is a dense, refractory, self-flowing concrete with low cement content intended for use in aggressive environments, including contact with molten metals and slags at temperatures up to 1,900°C, especially for the production of monolithic linings of steel ladles, elements of the metal tract and as a repair concrete mass. It can be used for monolithic linings as well as for products of any configuration and complexity. — high temperature resistance — high temperature of liquid phase formation — high mechanical strength — high temperature of onset of deformation under load — does not contain substances that cause allergic reactions — resistant to molten metal, acid and alkaline slags Main application: ferrous, non-ferrous and glass industry, lining of melting aggregates in the production of mineral fibres etc.

Sable correcteur, sable pour sols équestres, sable pour filtration, sable pour sols sportifs, sable stabilisé

Nos graviers respectent la norme CE de marquage des granulats, tant du point de vue de la dureté que de la granulométrie. Deux d’entre eux, le 2/6 mm et le 6/20 mm, respectent en outre la norme BENOR, nécessaire pour fabriquer du béton. 2/6 mm (CE, BENOR) 6/14 mm (CE) 6/20 mm (CE, BENOR) 20/32 mm (CE)

Dans ce type d’application, on utilise un granulat de marbre avec un large éventail de couleur et de dimension des granulés de marbre. Une couche de finition d’environ 15 mm est posée au-dessus d’un support solide à base du ciment. Ensuite le sol est poncé avec des machines à segments de diamant afin de faire exposer les grains.

Als Service-Partner der Schüttgut verarbeitenden Industrie, entwickeln und realisieren wir mit Ihnen Ihr individuelles Projekt im Bereich Granulierung und Kompaktierung. Die Herstellung und Verarbeitung von Granulaten bietet eine Reihe von Vorteilen gegenüber dem Einsatz nicht-granulierter Feststoffe: So weisen Granulate eine verbesserte Fließ- und Haftfähigkeit auf, vorteilhaft beim Verpressen zu Tabletten. Die Gleichmäßigkeit der Granulate ermöglicht eine höhere Dosiergenauigkeit und die homogene Verteilung der Wirkstoffe. Da sich nicht alle Rohstoffe in trockenem Zustand optimal verarbeiten lassen, bieten wir unseren Kunden auch für diesen Fall die passende Lösung: Die Feuchtgranulation.

Mezcla de aditivos, condimentos y especias, de uso charcutero, para la elaboración del producto cárnico tratado por el calor denominado “Morcilla”. Formato: bolsa 5kg

Optimale Wärmedämmeigenschaften (Einsparung der Heizenergie bis zu 25% gegenüber Normalmörtel) bei hoher Druckfestigkeit. Mit Leichtmauermörtel können einschalige Außenwände ohne zusätzliche Dämmschicht wirtschaftlich erstellt werden. Optimale Wärmedämmeigenschaften (Einsparung der Heizenergie bis zu 25% gegenüber Normalmörtel) bei hoher Druckfestigkeit. Guter Schallschutz, leicht verarbeitbar, ökologisch und sehr wirtschaftlich durch einschalige Bauweise. Wird werkfrisch angeliefert – pünktlich! • LM21 besteht aus hochwertigen Leichtzuschlagstoffen für beste Wärmeleitfähigkeit. • LM36 für wärmedämmendes Mauerwerk mit besten Verarbeitungseigenschaften.

Mesures : 5x5x5 / 7x10x10 / 10x10x10 / 5x10x10 / 15x17 / 20x10x10 ... Finitions : Fissuré / Éclate / Scié / Granulé / Bouchardé / Flammé / Sablée / Polie Poids M3 : 2660 kg Format : Couper à la mesure Conditionnement : En vrac / Boîtes en bois / Big Bags (sacs) Transport : Camion / Bateau Délai : 3-5 jours Résistance Compression : 2260 kg / cm2 Absorption d'eau : 0.2 % Porosité : 0.5 % Résistance à l'usure : 0.2 mm Résistance Glace : plus de 240 cycles de glace Port : Leixões Minimum : 24 Tonnes Résistance Chocs : 65 cm Résistance Glace après : 2090 kg / cm2 Résistance Flexion : 162 kg / cm2

Mugla Silver Marble Slab is a luxurious natural stone product that is perfect for any home or commercial space. Its striking silver-grey color with natural veining is sure to add a touch of sophistication and elegance to any design.

Les blocs de coffrage sont utilisées pour la réalisation de murs de soutènement, pour les structures soumises à de fortes charges latérales et de compressions. On les emploie par exemple pour les piscines, réservoirs, citernes, caves. Leur pose étant réalisée à sec* (sans mortier), elle est à la fois simple et rapide. Dimensions (en cm): 50x20x25 50x20x27 *sous réserve d'avis technique.

Es un abrasivo elaborado con minerales naturales, resistente, reutilizable y sin hierro. Dureza: 7.5-8.5 mohs Forma: angular Densidad: 3,5-4,0 g / cm3

HIMacs, Corian und Varicor Mineralwerkstoff, kommt mehr oder weniger aus den medizinischen Bereichen, da es antibakteriell, leicht zu reinigen, fugenlos und gegen sämtliche Desinfektionsmittel beständig ist. Wir sind damit aber auch immer mehr im Bad unterwegs, Waschbecken und duschen. Natürlich immer in Zusammenarbeit mit Fliesenleger und Sanitärer.

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

Un béton lissé s’obtient par passage d’une lisseuse manuelle ou mécanique (hélicoptère) jusqu’à l’obtention d’une surface lisse à la surface du béton frais commençant sa prise, le béton faisant l’objet ou non d’un traitement superficiel par saupoudrage ou topping. Nos marques (déposées) : MINHARDUR® mécanique : Le béton lissé mécaniquement à l’aide d’une truelle mécanique s’adapte aux grandes surfaces. On peut ensuite opter pour une finition en béton cristallisé pour lui conférer un éclat hors du commun et une meilleure résistance aux taches. MINHARDUR® manuel : Le béton lissé manuellement s’adapte à toutes les surfaces. Ce travail entièrement parachevé manuellement présente des effets plus marqués que les sols lissés manuellement. Type de finition conseillé : traitement bouche-pores comme protection contre les taches

CBG-DP-90 ist ein dichter, feuerfester, selbstfließender Beton mit niedrigem Zementgehalt, der für den Einsatz in aggressiven Umgebungen, einschließlich Kontakt mit geschmolzenen Metallen und Schlacken bei Temperaturen von bis zu 1.900°C, insbesondere für die Herstellung von monolithischen Auskleidungen von Stahlpfannen, Elementen des Metalltrakts und als Reparaturbetonmasse bestimmt ist. Er kann sowohl für monolithische Auskleidungen als auch für Produkte beliebiger Konfiguration und Komplexität verwendet werden. — hohe Temperaturbeständigkeit — hohe Temperatur der Flüssigphaseentstehung — hohe mechanische Belastbarkeit — hohe Temperatur beim Einsetzen der Verformung unter Last — enthält keine Stoffe, die allergische Reaktionen hervorrufen — beständig gegen Metallschmelze, saure und alkalische Schlacken Hauptanwendung: Eisen-, Nichteisen- und Glasindustrie, Auskleidung von Schmelzaggregaten bei Herstellung von Mineralfasern etc. Zusammensetzung:Korund, Tabulartonerde, Spinell Bindung:Hydraulisch Anwendungstemperatur:bis zu 1 .900°C Temperaturwechselbeständigkeit:> 40 Wasserabkühlzyklen von 1300°C bis auf Kühlwassertemperatur Temperatur bei Beginn der Verformung unter Last 0,2 MPa:1 .850°С Dichte:2.850 kg/m³ Maximale Korngröße:10 mm Wasserverbrauch:5,0-5,3 l/100 kg Chemische Zusammensetzung:Al2O3 - 88,5 % ; MgO - 0,5 % ; Cr2O3 - 2,5 % ; Fe2O3 - 0,5 % ; CaO - 5,0% Dichte (g/cm³):2,85 (bei Temp. 110 °C) ; 2,85 (bei Temp. 800 °C) ; 2,90 (bei Temp. 1350 °C) Wärmeleitfähigkeit (W/m∙K):1,94 (bei Temp. 110 °C) ; 2,56 (bei Temp. 800 °C) ; 2,70 (bei Temp. 1350 °C) Druckfestigkeit (MPa):85 (bei Temp. 110 °C) ; 80 (bei Temp. 800 °C) ; 110 (bei Temp. 1350 °C) Restliche lineare Deformation (%):0 (bei Temp. 110 °C) ; 0 (bei Temp. 800 °C) ; -0,1 (bei Temp. 1350 °C) Offene Porosität (%):n.a. (bei Temp. 110 °C) ; 16,0 (bei Temp. 800 °C) ; 14,9 (bei Temp. 1350 °C)

Nos graviers respectent la norme CE de marquage des granulats, tant du point de vue de la dureté que de la granulométrie. Deux d’entre eux respectent en outre la norme BENOR, nécessaire pour couler du béton. 2/6 mm (CE, BENOR) 6/14 mm (CE) 6/20 mm (CE,BENOR) 20/32 mm (CE)

Les produits broyés sont les produits historiques de la carrière, expérimentée dans ce domaine depuis plus de 150 ans. Ils sont essentiellement utilisés en verrerie, et peuvent, à la demande, être séchés, défillérisés (on parle alors de 0,1/2mm) et éventuellement réhumidifiés. Leur faible taux d’impureté en aluminium et en fer et leur haut taux en calcaire (>98,5%) en font un produit de choix, introuvable ailleurs à 250 kilomètres à la ronde. Ils peuvent être, au choix, chargés par péniches (jusque 1350 T) ou par camions. Contactez-nous pour des informations complémentaires